Art3d 19.7″ x 19.7″ (Pack Of 12) Wall Panel Rectangle, Black

Inexpensive option for cool wall treatment
Panels are thin plastic, found the best method of cutting was a really sharp pair of kitchen sheers. Draw a straight line on the back side in pencil using a square, and it should work out fine. If you have to cut an end that leaves a hole, the way I got around it was to use a scrap piece and basically cut a filler piece to cover the hole. I used a couple small dabs of super glue to hold the “cap” in place. Overall if you take your time and plan your pattern, it wasn’t too bad to work with. It’s an inexpensive option, some other styles that are solid, are much more expensive.

Really cool tiles that make a big statement.
These tiles make a really nice looking accent wall. They are very durable and easy to put up. Went up fast with just construction adhesive on the back. Cutting out outlets was the only challenge. I used an oscillating tool to cut them out and it went fairly well. Tinsnips would work as well. If you have to cut a bunch of tiles the same for a wall end or ceiling and have a table saw you can use it to cut a stack of tiles at the same time. I did 6 at a time and it cut them all with a neat edge. Very happy overall.

Awesome Product!!
FYI: I did all of the TLC in the images by myself. I went bold and did the entire bathroom walls, not just an accent wall; using the heavy-duty PVC by Art3D to the walls and the ceilings was done using a softer insulated PE foam brick version also available from numerous sellers on Amazon. (1 of 4 units is completed and fully rented and I have 3 more to go) I’d have to say that you’d need a very strong adhesive such as “Tite Bond” or similar (available at Menards for instance). Your typical liquid nails wouldn’t do, as you need something strong enough that would quickly set and create a strong enough bond for the tiles not to fall off.CUTTING: With respect to cutting the tough PVC tiles, I found that cutting from the back-side using my Milwaukee Hackzhall (basically a powerful light-weight portable sawzhall that can easily be controlled one-handed) along with a special universal DIAMOND-BLADE, which can be purchased at your local hard-ware store, did the trick. This blade with diamond bits/chips on the edge, along with the hackzhall, cut through the PVC like sword through butter and allowed me to make some critical/difficult cuts. To further trim the PVC, I used very sharp/new shears to trim to size. Concerning cutting-out for the outlets, etc., I flip the tile and use a sharp razor, but be very careful as the PVC is slick and you could slip or accidentally make the wrong cut; so you could also use a touch metal ruler to prevent/minimize slips of the razor. In my case, I like to recycle stuff, so I used remnants of the metal security door/bar that came from the top of the metal gate that was not used as a hard metal ruler. Remember, easy does it and safety comes first…The application is not too bad on a very flush/leveled wall. If your wall has uneven areas, be prepared to have to use weights of sorts to lean against it. This will delay installation as you may have to do this for every few tiles, or for a trouble section. I have had to use ladders and scaffolding in order to apply heavy weighs such as cinder bricks, clay bricks, and actual weights such as dumbbells and barbells as high as 7-8 ft off the ground to hold the tiles down just long enough to cure (dangerous, so not recommended, but as a Construction Tech, I know my limits and I always have my hard hat on…).The end results are stunning… Especially if you take the time to CAULK between the seams (this is an important extra step that separates the PROS from the mediocre). This hides the seams a lot better and creates a nice continuous seamless brick wall, and makes it all look more realistic. I have gotten nothing but positive review/feedback from all who saw the brick wall.I also did the utility room with the water lines for the electric hot water tank, the furnace, etc.., in the same 3D wall tiles and it looks stunning… Yes, the utility room was a bit of an overkill as the mechanicals will fill-up this room eventually, so you would not see much of the 3D wall, maybe a third of the wall would show if that. However, I personally wanted a challenge, and I wanted a permanent solution to the utility room often needing to be repainted after a few years. This is a more permanent maintenance-free solution, just as with the bathroom, as the wall-to-wall and ceiling tiling (who does that lol?), would offer air-tight, water-proof, low maintenance, easy clean-up look for many years to come, thus saving $$$ in the long run. I am sold on this product and I also purchased their 3D back-splash and would be reviewing before and after on that too. That was also a hit. I will return to buy a ton as I am now focusing my life-long dream/goal of TLC of real estate properties.

Great color and looks great on the wall
Why did you pick this product vs others?:They filled the space we needed really well. Added some flair to them to make an art piece. And love the navy color! 

facili da installare, dimensioni precise e veramente belli esteticamente

Amaaazing highly recommended

Pas beaucoup . c’est du plastique. Un petit coup ben tout s’enfonce. Vu le prix visuelle bien mais pas solide du tout.